I'm using dm368ipnc rdk 5.0 (provided by appropho).
But the it cannot boot.
My Log is :
DM368 IPNC :>boot
NAND read: device 0 offset 0x700000, size 0x1000000
16777216 bytes read: OK
Loading from NAND 128MiB 3,3V 8-bit, offset 0x500000
Image Name: Linux-2.6.37_IPNC_DM368_5.0.0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3448576 Bytes = 3.3 MB
Load Address: 80008000
Entry Point: 80008000
## Booting kernel from Legacy Image at 80700000 ...
Image Name: Linux-2.6.37_IPNC_DM368_5.0.0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3448576 Bytes = 3.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Linux version 2.6.37_IPNC_DM368_5.0.0 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Tue Dec 10 01:43:54 CST 2013
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: DaVinci DM36x IPNC
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] DaVinci dm36x_rev1.2 variant 0x8
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 14224
[ 0.000000] Kernel command line: mem=56M console=ttyS1,115200n8 root=/dev/ram0 rw initrd=0x82000000,20M ip=dhcp eth=$(ethaddr)
[ 0.000000] TI DaVinci EMAC: kernel boot params Ethernet address: $(ethaddr)
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 56MB = 56MB total
[ 0.000000] Memory: 53304k/53304k available, 4040k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xc4000000 - 0xfea00000 ( 938 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc3800000 ( 56 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0028000 ( 128 kB)
[ 0.000000] .text : 0xc0028000 - 0xc032d000 (3092 kB)
[ 0.000000] .data : 0xc032e000 - 0xc0351f00 ( 144 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:245
[ 0.000000] Console: colour dummy device 80x30
[ 0.000408] Calibrating delay loop... 147.86 BogoMIPS (lpj=739328)
[ 0.220092] pid_max: default: 32768 minimum: 301
[ 0.220519] Mount-cache hash table entries: 512
[ 0.221578] CPU: Testing write buffer coherency: ok
[ 0.223761] devtmpfs: initialized
[ 0.227766] DaVinci: 8 gpio irqs
[ 0.228599] NET: Registered protocol family 16
[ 0.361615] bio: create slab <bio-0> at 0
[ 0.367766] SCSI subsystem initialized
[ 0.373186] usbcore: registered new interface driver usbfs
[ 0.374935] usbcore: registered new interface driver hub
[ 0.376102] usbcore: registered new device driver usb
[ 0.380712] vpss vpss: dm365_vpss vpss probed
[ 0.380800] vpss vpss: dm365_vpss vpss probe success
[ 0.383262] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.385850] Switching to clocksource timer0_1
[ 0.390122] Switched to NOHz mode on CPU #0
[ 0.479686] NET: Registered protocol family 2
[ 0.480103] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.481196] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.481399] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.481530] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.481577] TCP reno registered
[ 0.481627] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.481714] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.482404] NET: Registered protocol family 1
[ 0.573681] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.578760] msgmni has been set to 104
[ 0.582409] io scheduler noop registered (default)
[ 0.584538] CSL: Module install successful, device major num = 254
[ 0.584604] CSL: Module version 0.10.00, built on Dec 10 2013 01:25:13
[ 0.584678] I2C: Module install successful, device major num = 253
[ 0.584739] DMA: Module install successful, device major num = 252
[ 0.584778] DRV: Module install successful
[ 0.584815] DRV: Module built on Dec 10 2013 01:25:17
[ 0.584855] DRV: EDMACC.QUEPRI = 00002777
[ 0.584888] DRV: SYSTEM.MSTPRI0 = 00440011
[ 0.584920] DRV: SYSTEM.MSTPRI1 = 00000444
[ 0.584952] DRV: ISP.BCR = 00000002
[ 0.584984] DRV: SYSTEM.MISC = 00000311
[ 0.585018] EDMAK module: built on Dec 10 2013 at 01:24:33
[ 0.585063] Reference Linux version 2.6.37
[ 0.585098] File /opt/workdir/IMX036_Ver5_0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
[ 0.587445] IRQK module: built on Dec 10 2013 at 01:10:43
[ 0.587515] Reference Linux version 2.6.37
[ 0.587553] File /opt/workdir/IMX036_Ver5_0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
[ 0.589621] irqk initialized
[ 0.589728] CMEMK module: built on Dec 10 2013 at 01:24:27
[ 0.589787] Reference Linux version 2.6.37
[ 0.589825] File /opt/workdir/IMX036_Ver5_0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
[ 0.591842] no physical memory specified, continuing with no memory allocation capability...
[ 0.591985] cmemk initialized
[ 0.592041] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.617834] serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
[ 0.640704] serial8250.0: ttyS1 at MMIO 0x1d06000 (irq = 41) is a 16550A
[ 1.118891] console [ttyS1] enabled
[ 1.127323] brd: module loaded
[ 1.141991] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung )
[ 1.151340] Bad block table not found for chip 0
[ 1.158158] Bad block table not found for chip 0
[ 1.162809] Scanning device for bad blocks
[ 1.168224] Bad eraseblock 9 at 0x000000120000
[ 1.208298] Bad eraseblock 312 at 0x000002700000
[ 1.213009] Bad eraseblock 313 at 0x000002720000
[ 1.217793] Bad eraseblock 314 at 0x000002740000
[ 1.222496] Bad eraseblock 315 at 0x000002760000
[ 1.227304] Bad eraseblock 316 at 0x000002780000
[ 1.232013] Bad eraseblock 317 at 0x0000027a0000
[ 1.236814] Bad eraseblock 318 at 0x0000027c0000
[ 1.241522] Bad eraseblock 319 at 0x0000027e0000
[ 1.246324] Bad eraseblock 320 at 0x000002800000
[ 1.251032] Bad eraseblock 321 at 0x000002820000
[ 1.255727] Bad eraseblock 322 at 0x000002840000
[ 1.260528] Bad eraseblock 323 at 0x000002860000
[ 1.265239] Bad eraseblock 324 at 0x000002880000
[ 1.270042] Bad eraseblock 325 at 0x0000028a0000
[ 1.274751] Bad eraseblock 326 at 0x0000028c0000
[ 1.279552] Bad eraseblock 327 at 0x0000028e0000
[ 1.312725] Bad eraseblock 571 at 0x000004760000
[ 1.329009] Bad eraseblock 670 at 0x0000053c0000
[ 1.378150] Creating 8 MTD partitions on "davinci_nand.0":
[ 1.383702] 0x000000000000-0x000000300000 : "bootloader"
[ 1.394763] 0x000000300000-0x000000500000 : "params"
[ 1.405656] 0x000000500000-0x000000900000 : "kernel"
[ 1.416850] 0x000000900000-0x000003100000 : "filesystem1"
[ 1.428412] 0x000003100000-0x000003900000 : "data1"
[ 1.439451] 0x000003900000-0x000003d00000 : "Calibration"
[ 1.451048] 0x000003d00000-0x000006500000 : "filesystem2"
[ 1.462965] 0x000006500000-0x000008000000 : "data2"
[ 1.474364] davinci_nand davinci_nand.0: controller rev. 2.3
[ 1.487220] spi_davinci spi_davinci.0: Controller at 0xfec66000
[ 1.546071] davinci_mdio davinci_mdio.0: davinci mdio revision 1.4
[ 1.552301] davinci_mdio davinci_mdio.0: detected phy mask fffffffd
[ 1.560476] davinci_mdio.0: probed
[ 1.563943] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown
[ 1.572094] i2c /dev entries driver
[ 1.578746] Linux media interface: v0.10
[ 1.583613] Linux video capture interface: v2.00
[ 1.591247] vpbe-osd vpbe-osd: OSD sub device probe success
[ 1.598176] vpbe-venc vpbe-venc: VENC sub device probe success
[ 1.605317] vpbe-v4l2 vpbe-v4l2: vpbe v4l2 device registered
[ 1.611502] Setting default output to Composite
[ 1.616287] Setting default mode to ntsc
[ 1.620374] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.
[ 1.627230] vpbe-v4l2 vpbe-v4l2: layer=c3135600,layer->video_dev=c31356e8
[ 1.635196] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.
[ 1.642246] vpbe-v4l2 vpbe-v4l2: layer=c3135c00,layer->video_dev=c3135ce8
[ 1.651623] watchdog watchdog: heartbeat 60 sec
[ 1.663671] Error: Driver 'davinci-mcbsp' is already registered, aborting...
[ 1.674667] asoc: cq93vc-hifi <-> davinci-vcif mapping ok
[ 1.685462] ALSA device list:
[ 1.688875] #0: DaVinci DM365 EVM
[ 1.694096] TCP cubic registered
[ 1.697806] NET: Registered protocol family 17
[ 1.768790] net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, id=181b8b0)
[ 1.836125] Sending DHCP requests .
[ 3.766370] PHY: 0:01 - Link is Up - 100/Full
[ 3.866018] ., OK
[ 3.896086] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.10.101
[ 3.904329] IP-Config: Complete:
[ 3.907554] device=eth0, addr=192.168.10.101, mask=255.255.255.0, gw=192.168.10.1,
[ 3.915546] host=192.168.10.101, domain=, nis-domain=(none),
[ 3.921765] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
[ 3.930224] List of all partitions:
[ 3.933800] 1f00 3072 mtdblock0 (driver?)
[ 3.939069] 1f01 2048 mtdblock1 (driver?)
[ 3.944168] 1f02 4096 mtdblock2 (driver?)
[ 3.949395] 1f03 40960 mtdblock3 (driver?)
[ 3.954492] 1f04 8192 mtdblock4 (driver?)
[ 3.959702] 1f05 4096 mtdblock5 (driver?)
[ 3.964804] 1f06 40960 mtdblock6 (driver?)
[ 3.970000] 1f07 27648 mtdblock7 (driver?)
[ 3.975072] No filesystem could mount root, tried: vfat msdos
[ 3.981046] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)
[ 3.989391] Backtrace:
[ 3.991876] Function entered at [<c002c4ec>] from [<c02c11e0>]
[ 3.997799] r7:00008000 r6:c3013000 r5:c0022b2c r4:c0352660
[ 4.003527] Function entered at [<c02c11c8>] from [<c02c124c>]
[ 4.009454] Function entered at [<c02c11e4>] from [<c0008f84>]
[ 4.015306] r3:00000000 r2:00000020 r1:c3027f60 r0:c02ddae1
[ 4.021102] Function entered at [<c0008d20>] from [<c0009030>]
[ 4.027019] Function entered at [<c0008fdc>] from [<c00091a8>]
[ 4.032871] r5:c0022ae4 r4:c0351f68
[ 4.036552] Function entered at [<c0009048>] from [<c00084b4>]
[ 4.042400] r5:c00222c8 r4:c0351f18
[ 4.046073] Function entered at [<c00083a4>] from [<c0040e28>]
[ 4.051924] r5:c00083a4 r4:00000000
How can I solve any problems?
If my bootcmd or bootargs is wrong, then what is the correct bootcmd/bootargs?
I really want to make the camera boot.